DPA 4098 CORE floor stand
A complete cardioid microphone floor stand solution, offering a high-quality stage voice or instrument mic.
This floor stand solution has an elegant and exclusive design with a black, non-reflective surface specifically made to handle the, from time to time, rough life in TV-studios, OB-vans and onstage in theaters and concert halls. The floor base has an integrated shock mounting solution. The thread screw holds the stand extension and MMP-F modular active boom. This unique design allows for a long stage microphone boom pole that does not swing, but rapidly stabilizes itself after being positioned.
These floor stand solutions can quickly, and with no tools needed, transform into a new configuration. You can combine it with another pencil mic capsule and preamplifier.
FEATURES:
- low noise and natural voice
- highly directional for high isolation
- uniform, frequency independent directionality
- exclusive, elegant design
- integrated shock-mounting in floor base
- rapidly stabilizing microphone boom pole
- modular flexibility
INCLUDED WITH:
- 1x foam windscreen
GENERAL:
- directional pattern: supercardioid
- principle of operation: pressure gradient
- cartridge type: pre-polarized condenser
- frequency response: 20Hz-20 kHz
- effective frequency range +/-2 dB at 20 cm: MicroDot 80Hz-15kHz with 3dB soft boost at 8-15kHz & XLR-3M: 100Hz-15kHz with 3dB soft boost at 8-15 kHz and permanent 2nd order low-cut filter at 80Hz
- sensitivity, nominal, +/-3 dB at 1 kHz: 16 mV/Pa -36dB re. 1V/Pa
- equivalent noise level, A-weighted: typ. 23dB(A) re. 20µPa (max. 26dB(A))
- distortion, THD<1% Legacy: 122dB SPL RMS, 125dB SPL peak
- distortion, THD<1% CORE: 130dB SPL RMS, 133dB SPL peak
- dynamic range Legacy: typ. 102dB
- dynamic range CORE: typ. 110dB
- max. SPL, THD 10%: 135dB SPL peak
- rated output impedance: from MicroDot: 30-40 Ohm
- rated output impedance: from XLR connector or DAD6001-BC XLR Adapter: 100 Ohm
- minimum load impedance: 2 kOhm
- cable drive capability: MicroDot up to 300 m with DAD6001-BC XLR adapter & XLR-3M: up to 100m
- output balance principle: signal balanced with XLR connector or DAD6001-BC XLR adapter
- common mode rejection ratio (CMRR): >60dB from 50Hz to 15kHz with DAD6001-BC XLR adapter
- power supply (for full performance): MicroDot min. 5 V to max. 10 V through DPA adapter for wireless systems or P48 (Phantom Power) with DAD6001-BC XLR adapter OR XLR-3M: P48 (Phantom Power)
- current consumption: typ. 1.5 mA (microphone) & 3.5 mA with DAD6001-BC XLR adapter
- connector: MicroDot or XLR-3M
- color: black or white
WEIGHT:
Microdot:
- 16 cm: 12g
- 28 cm: 20g
- 43 cm: 28g
- 77 cm: 55g
- 122 cm: 67g
XLR-3M:
- 20cm: 75g
- 32cm: 80g
- 47cm: 88g
- 77cm: 115g
- 122cm : 127g
DIMENSIONS:
- microphone diameter: 5.7 mm
- microphone length: Microdot: 16cm, 28cm, 43cm, 77cm, 122cm & XLR-3M: 20cm, 32cm, 47cm, 77cm, 122cm
- polarity: +V at MicroDot pin for positive sound pressure (and pin 2 on XLR connector or DAD6001-BC XLR adapter)
- temperature range: -40°C to 45°C
- relative humidity (RH): up to 90%
| boom length | 122cm boom (top & bottom gooseneck) |
|---|---|
| Brand | DPA |
