DPA 3511A
3511A is a complete stereo kit with two 4011A cardioid microphones, carefully factory-matched within +/-1dB on frequency response and sensitivity in the microphone's entire frequency bandwidth. The first-order cardioid pickup pattern provides superb separation between sound sources when used as a spot mic on literally any style of live music, from rock&roll to opera. The 4011A is equally suitable for close-up work on acoustic guitar, grand piano, overheads, percussion, wind instruments and vocals as it is for spot-miking symphonies. It can handle incredibly high sound levels and even includes a 20dB pad switch in the center of the XLR connector to attenuate the output of the microphone. A flat on-axis frequency response and excellent phase response deliver a totally faithful reproduction of the original sound. The off-axis response is similarly smooth so that any leakage is an accurate reflection of the original, though attenuated according to the true first-order cardioid pickup pattern. The sensation of "being there" will always be more intense with the DPA 4011A than with any other cardioid. Chosen for its qualities as an all-around performer, the 4011A is a great, clean-sounding colorless mic. The variety of applications is as wide as the imagination of the user.
These cardioids are exceptionally linear in their frequency responses - also off-axis. Several standard set-ups such as ORTF and XY are possible. The 4011A's handle very high SPL and will allow for close-miking as well as more distant placement. They are often used for piano recordings of jazz or pop, overheads for drums or orchestra section stereo pair.
What's in the box
- 2x 4011A cardioid microphones, factory-matched
- 2x UA0897 shock mount
- 2x UA0896 foam windscreen for 2006C/4006C/4011/4015C
- 2x UA0961 microphone holder
- 1x DUA0019 spacer for stereo boom
- 1x UA0837 stereo boom excluding holder
- Directional pattern: cardioid
- Principle of operation: pressure gradient
- Cartridge type: pre-polarized condenser
- Frequency range: 20Hz to 20kHz
- Frequency range, +/-2dB: 40Hz to 20kHz
- Sensitivity, nominal, +/-2dB at 1kHz: 10mV/Pa, -28dB re. 1V/Pa
- Equivalent noise level, A-weighted: typ. 18dB(A) re. 20uPa (max. 20dB(A))
- Equivalent noise level, ITU-R BS.468-4: typ. 25dB (correct with the attenuator in 0 dB or -20 dB setting)
- S/N ratio (A-weighted), re. 1kHz at 1Pa (94dB SPL): typ. 76dB(A)
- Total harmonic distortion (THD): <1% up to 139dB SPL peak
- Dynamic range: typ. 121dB
- Max. SPL, peak before clipping: 159dB
- Switchable attenuator, filters etc.: 0dB / -20dB
- Output impedance: 200Ohm
- Minimum load impedance: 2kOhm
- Cable drive capability: 100m
- Output balance principle: Impedance balancing with "Active Drive"
- Common mode rejection ratio (CMRR): >60dB
- Power supply (for full performance): 48V Phantom power (+/-4V)
- Current consumption: 2.8mA
- Connector: XLR-3M. pin 1: shield, pin 2: signal + phase, pin 3: phase
- Color: matte black
- Weight: 158g
- Microphone/capsule diameter: 19/19mm
- Microphone length: 170mm
- Maximum output voltage, RMS: >5V
- Polarity: +V at pin 2 for positive sound pressure
- Temperature range: -40°C to 45°C
- Relative humidity (RH): up to 90%
- Matching tolerance (frequency response and sensitivity): +/-1dB
- Phase deviation for kit: <10°
Brand | DPA |
---|